Liquefaction Resistance of Soils: Summary Report from the 1996 NCEER and 1998 NCEER/NSF Workshops on Evaluation of Liquefaction Resistance of Soils
This article has a reply.
VIEW THE REPLYPublication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 127, Issue 10
Abstract
Following disastrous earthquakes in Alaska and in Niigata, Japan in 1964, Professors H. B. Seed and I. M. Idriss developed and published a methodology termed the “simplified procedure” for evaluating liquefaction resistance of soils. This procedure has become a standard of practice throughout North America and much of the world. The methodology which is largely empirical, has evolved over years, primarily through summary papers by H. B. Seed and his colleagues. No general review or update of the procedure has occurred, however, since 1985, the time of the last major paper by Professor Seed and a report from a National Research Council workshop on liquefaction of soils. In 1996 a workshop sponsored by the National Center for Earthquake Engineering Research (NCEER) was convened by Professors T. L. Youd and I. M. Idriss with 20 experts to review developments over the previous 10 years. The purpose was to gain consensus on updates and augmentations to the simplified procedure. The following topics were reviewed and recommendations developed: (1) criteria based on standard penetration tests; (2) criteria based on cone penetration tests; (3) criteria based on shear-wave velocity measurements; (4) use of the Becker penetration test for gravelly soil; (4) magnitude scaling factors; (5) correction factors for overburden pressures and sloping ground; and (6) input values for earthquake magnitude and peak acceleration. Probabilistic and seismic energy analyses were reviewed but no recommendations were formulated.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Ambraseys, N. N. (1988). “Engineering seismology.” Earthquake Engrg. and Struct. Dynamics, 17, 1–105.
2.
Andrus, R. D., and Stokoe, K. H., II (1997). “Liquefaction resistance based on shear wave velocity.” Proc., NCEER Workshop on Evaluation of Liquefaction Resistance of Soils, Nat. Ctr. for Earthquake Engrg. Res., State Univ. of New York at Buffalo, 89–128.
3.
Andrus, R. D., and Stokoe, K. H., II (2000). “Liquefaction resistance of soils from shear-wave velocity.”J. Geotech. and Geoenvir. Engrg., ASCE, 126(11), 1015–1025.
4.
Arango, I. (1996). “Magnitude scaling factors for soil liquefaction evaluations.”J. Geotech. Engrg., ASCE, 122(11), 929–936.
5.
ASTM. (2000). “Annual book of ASTM standards.” 04.08, D 1586-99, West Conshohocken, Pa.
6.
Castro, G. (1995). “Empirical methods in liquefaction evaluation.” Primer Ciclo d Conferencias Internationales, Leonardo Zeevaert, Universidad Nacional Autonoma de Mexico, Mexico City.
7.
Finn, W. D. L., Martin, G. R., and Lee, K. W. (1977). “An effective stress model for liquefaction.”J. Geotech. Engrg Div., ASCE, 103(6), 517—533.
8.
Gibbs, H. J., and Holtz, W. G. (1957). “Research on determining the density of sand by spoon penetration testing.” Proc., 4th Int. Conf. on Soil Mech. and Found. Engrg., Vol. I, 35–39.
9.
Gilstrap, S. D., and Youd, T. L. (1998). “CPT based liquefaction resistance analyses using case histories.” Tech. Rep. CEG-90-01, Dept. of Civ. and Envir. Engrg., Brigham Young University, Provo, Utah.
10.
Golesorkhi, R. (1989). “Factors influencing the computational determination of earthquake-induced shear stresses in sandy soils.” PhD dissertation, University of California at Berkeley.
11.
Harder, L. F., Jr. (1988). “Use of penetration tests to determine the cyclic loading resistance of gravelly soils during earthquake shaking.” PhD dissertation, University of California at Berkeley.
12.
Harder, L. F., Jr. (1997). “Application of the Becker Penetration test for evaluating the liquefaction potential of gravelly soils.” Proc., NCEER Workshop on Evaluation of Liquefaction Resistance of Soils, National Center for Engineering Research, Buffalo, 129–148.
13.
Harder, L. F., Jr. and Boulanger, R. W. (1997). “Application of Kσ and Kα correction factors.” Proc., NCEER Workshop on Evaluation of Liquefaction Resistance of Soils, Nat. Ctr. for Earthquake Engrg. Res., State Univ. of New York at Buffalo, 167–190.
14.
Harder, L. F., Jr. and Seed, H. B. (1986). “Determination of penetration resistance for coarse-grained soils using the Becker hammer drill.” Rep. UCB/EERC-86/06, Earthquake Engrg. Res. Ctr., University of California at Berkeley.
15.
Hynes, M. E., and Olsen, R. S. (1999). “Influence of confining stress on liquefaction resistance.” Proc., Int. Workshop on Phys. and Mech. of Soil Liquefaction, Balkema, Rotterdam, The Netherlands, 145–152.
16.
Idriss, I. M. (1985). “Evaluating seismic risk in engineering practice.” Proc., 11th Int. Conf. on Soil Mech. and Found. Engrg., Vol. 1, 255–320.
17.
Idriss, I. M. (1990). “Response of soft soil sites during earthquakes.” Proc., H. Bolton Seed Memorial Symp., Vol. 2, BiTech Publishers, Ltd., Vancouver, 273–290.
18.
Idriss, I. M. (1991). “Earthquake ground motions at soft soil sites.” Proc., 2nd Int. Conf. on Recent Adv. in Geotech. Earthquake Engrg. and Soil Dyn., Vol. 3, 2265–2271.
19.
Kayen, R. E., and Mitchell, J. K. (1997). “Assessment of liquefaction potential during earthquakes by Arias intensity.”J. Geotech. and Geoenvir. Engrg., ASCE, 123(12), 1162–1174.
20.
Kayen, R. E., Mitchell, J. K., Seed, R. B., Lodge, A., Nishio, S., and Coutinho, R. (1992). “Evaluation of SPT-, CPT-, and shear wave-based methods for liquefaction potential assessment using Loma Prieta data.” Proc., 4th Japan-U.S. Workshop on Earthquake-Resistant Des. of Lifeline Fac. and Countermeasures for Soil Liquefaction, Vol. 1, 177–204.
21.
Kramer S. L. (1996). Geotechnical earthquake engineering, Prentice-Hall, Englewood Cliffs, N.J., 653.
22.
Liao, S., and Whitman, R. V. (1986a). “Overburden correction factors for SPT in sand.”J. Geotech. Engrg., ASCE, 112(3), 373–377.
23.
Liao, S. S. C., Veneziano, D., and Whitman, R. V. (1988). “Regression models for evaluating liquefaction probability.”J. Geotech. Engrg., ASCE, 114(4), 389–411.
24.
Liao, S. S. C., and Whitman, R. V. (1986b). “Catalogue of liquefaction and non-liquefaction occurrences during earthquakes.” Res. Rep., Dept. of Civ. Engrg., Massachusetts Institute of Technology, Cambridge, Mass.
25.
Lodge, A. L. (1994). “Shear wave velocity measurements for subsurface characterization.” PhD dissertation, University of California at Berkeley.
26.
Marcuson, W. F., III (1978). “Definition of terms related to liquefaction.”J. Geotech. Engrg. Div., ASCE, 104(9), 1197–1200.
27.
Marcuson, W. F., III, and Bieganousky, W. A. (1977a). “Laboratory standard penetration tests on fine sands.”J. Geotech. Engrg. Div., ASCE, 103(6), 565–588.
28.
Marcuson, W. F., III, and Bieganousky, W. A. (1977b). “SPT and relative density in coarse sands.”J. Geotech. Engrg. Div., ASCE, 103(11), 1295–1309.
29.
National Research Council (NRC). (1985). Liquefaction of soils during earthquakes, National Academy Press, Washington, D.C.
30.
Olsen, R. S. (1984). “Liquefaction analysis using the cone penetrometer test (CPT).” Proc., 8th World Conf. on Earthquake Engrg., Vol. 3, 247–254.
31.
Olsen, R. S. (1997). “Cyclic liquefaction based on the cone penetration test.” Proc., NCEER Workshop on Evaluation of Liquefaction Resistance of Soils, Nat. Ctr. for Earthquake Engrg. Res., State Univ. of New York at Buffalo, 225–276.
32.
Robertson, P. K. (1990). “Soil classification using CPT.” Can. Geotech. J., Ottawa, 27(1), 151–158.
33.
Robertson, P. K., and Fear, C. E. (1995). “Liquefaction of sands and its evaluation.” Proc., 1st Int. Conf. on Earthquake Geotech. Engrg.
34.
Robertson, P. K., Woeller, D. J., and Finn, W. D. (1992). “Seismic cone penetration test for evaluating liquefaction potential under cyclic loading.” Can. Geotech. J., Ottawa, 29, 686–695.
35.
Robertson, P. K., and Wride, C. E. (1998). “Evaluating cyclic liquefaction potential using the cone penetration test.” Can. Geotech. J., Ottawa, 35(3), 442–459.
36.
Schnabel, P. B., Lysmer, J., and Seed, H. B. (1972). “A computer program for earthquake response analysis of horizontally layered sites.” Rep. No. EERC 72-12, University of California at Berkeley.
37.
Seed, H. B. (1979). “Soil liquefaction and cyclic mobility evaluation for level ground during earthquakes.”J. Geotech. Engrg. Div., ASCE, 105(2), 201–255.
38.
Seed, H. B. (1983). “Earthquake-resistant design of earth dams.” Proc., Symp. Seismic Des. of Earth Dams and Caverns, ASCE, New York, 41–64.
39.
Seed, H. B., and Idriss, I. M. (1971). “Simplified procedure for evaluating soil liquefaction potential.”J. Geotech. Engrg. Div., ASCE, 97(9), 1249–1273.
40.
Seed, R. B., Dickenson, S. E., Rau, G. A., White, R. K., and Mok, C. M. (1994). “Site effects on strong shaking and seismic risk: Recent developments and their impact on seismic design codes and practice.” Proc., Struct. Congr. II, Vol. 1, ASCE, New York, 573–578.
41.
Seed, R. B., and Harder, L. F., Jr. (1990). “SPT-based analysis of cyclic pore pressure generation and undrained residual strength.” Proc., H. Bolton Seed Memorial Symp., BiTech Publishers Ltd., Vancouver, 351–376.
42.
Seed, H. B., and Idriss, I. M. (1982). “Ground motions and soil liquefaction during earthquakes.” Earthquake Engineering Research Institute Monograph, Oakland, Calif.
43.
Seed, H. B., Tokimatsu, K., Harder, L. F., and Chung, R. M. (1985). “The influence of SPT procedures in soil liquefaction resistance evaluations.”J. Geotech. Engrg., ASCE, 111(12), 1425–1445.
44.
Skempton, A. K. (1986). “Standard penetration test procedures and the effects in sands of overburden pressure, relative density, particle size, aging, and overconsolidation.” Géotechnique, London, 36(3), 425–447.
45.
Stark, T. D., and Olson, S. M. (1995). “Liquefaction resistance using CPT and field case histories.”J. Geotech. Engrg., ASCE, 121(12), 856–869.
46.
Stokoe, K. H., II, Lee, S. H. H., and Knox, D. P. (1985). “Shear moduli measurements under true triaxial stresses.” Advances in the art of testing under cyclic conditions, ASCE, New York, 166–185.
47.
Suzuki, Y., Tokimatsu, K., Koyamada, K., Taya, Y., and Kubota, Y. (1995). “Field correlation of soil liquefaction based on CPT data.” Proc., Int. Symp. on Cone Penetration Testing, Vol. 2, 583–588.
48.
Sy, A., and Campanella, R. G. (1994). “Becker and standard penetration tests (BPT-SPT) correlations with consideration of casing friction.” Can. Geotech. J., Ottawa, 31, 343–356.
49.
Sy, A., Campanella, R. G., and Stewart, R. A. (1995). “BPT-SPT correlations for evaluation of liquefaction resistance in gravelly soils.” Proc., Spec. Session on Dyn. Properties of Gravelly Soil, ASCE, New York.
50.
Sykora, D. W. (1987). “Creation of a data base of seismic shear wave velocities for correlation analysis.” Geotech. Lab. Misc. Paper GL-87-26, U.S. Army Engr. Waterways Experiment Station, Vicksburg, Miss.
51.
Transportation Research Board (TRB). (1999). “TRB workshop on new approaches to liquefaction analysis.” Publ. No. FHWA-RD-99-165, Federal Highway Administration, Washington, D.C. (on CD-ROM).
52.
Tokimatsu, K., and Uchida, A. (1990). “Correlation between liquefaction resistance and shear wave velocity.” Soils and Found., Tokyo, 30(2), 33–42.
53.
Vreugdenhil, R., Davis, R., and Berrill, J. (1994). “Interpretation of cone penetration results in multilayered soils.” Int. J. Numer. and Analytical Methods in Geomech., 18, 585–599.
54.
Youd, T. L. (1993). “Liquefaction-induced lateral spread displacement.” NCEL Tech. Note N-1862, U.S. Navy, Port Hueneme, Calif., 44.
55.
Youd, T. L., and Hoose, S. N. (1977). “Liquefaction susceptibility and geologic setting.” Proc., 6th World Conf. on Earthquake Engrg., Vol. 3, Prentice-Hall, Englewood Cliffs, N.J., 2189–2194.
56.
Youd, T. L., and Idriss, I. M., eds. (1997). Proc., NCEER Workshop on Evaluation of Liquefaction Resistance of Soils, Nat. Ctr. for Earthquake Engrg. Res., State Univ. of New York at Buffalo.
57.
Youd, T. L., Kayen, R. E., and Mitchell, J. K. (1997). “Liquefaction criteria based on energy content of seismograms.” Proc., NCEER Workshop on Evaluation of Liquefaction Resistance of Soils, Nat. Ctr. for Earthquake Engrg. Res., State Univ. of New York at Buffalo, 217–224.
58.
Youd, T. L., and Noble, S. K. (1997a). “Magnitude scaling factors.” Proc., NCEER Workshop on Evaluation of Liquefaction Resistance of Soils, Nat. Ctr. for Earthquake Engrg. Res., State Univ. of New York at Buffalo, 149–165.
59.
Youd, T. L., and Noble, S. K. (1997b). “Liquefaction criteria based on statistical and probabilistic analyses.” Proc., NCEER Workshop on Evaluation of Liquefaction Resistance of Soils, Nat. Ctr. for Earthquake Engrg. Res., State Univ. of New York at Buffalo, 201–215.
60.
Youd, T. L., and Perkins, D. M. (1978). “Mapping of liquefaction-induced ground failure potential.”J. Geotech. Engrg. Div., ASCE, 104(4), 433–446.
Information & Authors
Information
Published In
History
Received: Jan 18, 2000
Published online: Oct 1, 2001
Published in print: Oct 2001
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.