Engineering Method for Air-Cooling Design of Two-Seat Propeller-Driven Aircraft Powered by Fuel Cells
Publication: Journal of Aerospace Engineering
Volume 24, Issue 1
Abstract
The application of fuel-cell technology to aircraft propulsion and/or energy supply is becoming of great interest for undoubted advantages in terms of pollution emissions and noise, features particularly important for commuter airplanes that usually take off and land from and in urban areas. The conversion of conventional aircraft into more/all-electric one tends to be based on the installation of such innovative systems. A better understanding of problems related to fuel cells applied to aeronautics is sought by the European Commission funded project environmentally friendly intercity aircraft powered by fuel cells (ENFICA-FC). The main objective of the ENFICA-FC project is to develop and to validate the use of a fuel-cell based power system for propulsion of an all-electric aircraft. The fuel-cell system will be installed in a light sport aircraft (Rapid 200) that will be flown and performance tested as a proof of functionality and future applicability. Specific aspects have to be investigated in the onboard installation of the innovative system and new design indications have to be pointed out in order to fulfill the conversion. One of the key items under investigation is the simulation of existing cooling system and the evaluation of motor and fuel-cell temperature; the temperature has to be maintained within the limits established by manufacturers of critical systems during all likely operating conditions as indicated by aeronautic regulations for general aviation. The computational problem addressed in this paper is the numerical computational fluid dynamics (CFD) simulation of the existing air-cooling system that satisfies air request for cooling and venting. An engineering model has been developed and it is used to support air inlet and outlet design. The flow is reasonably approximated by a potential flow plus boundary layer; hence, total upstream pressure losses are neglected except for those within the thin boundary layer. Pressure recovery of incoming cooling air and pressure coefficient distribution have been studied by using VSAERO panel code, and the optimal position of cooling and venting intakes is defined according to aerodynamic results. Propeller effects are included by referring to an optimal propeller specifically designed for the ENFICA-FC project. Propeller slip-stream wake is modeled by an actuator disk plus a swirl membrane and used to study the problem of motor, electronic, and fuel cells’ cooling during takeoff.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The activity has been developed within the ENFICA-FC project. The writers acknowledge the important contribution of European Commission by the funding programs ENFICA-FC, EC 6th FP—Contract No. UNSPECIFIEDAST5-CT-2006-030779.
References
Caisheng, W., Hashem, N., and Steven, R. S. (2005). “Dynamic models and model validation for PEM fuel cells using electrical circuits.” IEEE Trans. Energy Convers., 20(2), 442–451.
Corsiglia, V. R., Katz, J., and Kroeger, R. A. (1981). “Full-scale wind-tunnel study of the effect of nacelle shape on cooling drag.” J. Aircr., 18(2), 82–88.
D’Angelo, S., Berardi, F., and Minisci, E. (2002). “Aerodynamic performances of propellers with parametric considerations on the optimal design.” Aeronaut. J., 106(1060), 313–320.
Ferrari, C. (1957). “Interaction problems.” Aerodynamic components of aircraft at high speeds, A. F. Donovan and H. R. Lawrence, eds., Princeton University Press, Princeton, N.J.
Glover, B. (2005). “Fuel cells opportunity.” Proc., AIAA/AAAF Aircraft Noise and Emissions Reduction Symp., AIAA, Reston, Va.
Holman, J. P. (2009). Heat transfer, McGraw-Hill, New York.
Jay, T., Pukrushpan, H., Peng, A., and Stefanopoulou, G. (2004). “Control-oriented modeling and analysis for automotive fuel cell systems.” J. Dyn. Syst., Meas., Control, 126(1), 14.
Katz, J., Corsiglia, V. R., and Barlow, P. R. (1982a). “Cooling air inlet exit geometries on aircraft engine installations.” J. Aircr., 19(7), 525–530.
Katz, J., Corsiglia, V. R., and Barlow, P. R. (1982b). “Effect of propeller on engine cooling system drag and performance.” J. Aircr., 19(3), 193–197.
Lienhard, J. H., IV, and Lienhard, J. H., V (2000). A heat transfer textbook, Phlogiston Press, Cambridge, Mass.
Liu, J. (2004). “Design and control of a kilo-amp DC/AC inverter for integrated starter-generator (ISG) applications.” IEEE-IAS'04, IEEE, New York, 2754-2761.
Natham, J. K. (2005). “A code for calculating the nonlinear aerodynamic characteristic of arbitrary configuration.” VSAERO user’s manual, JK Ananlytical Methods, Washington.
Phase Motion Control. (2007). “Technical information on TK frameless motors.” ⟨http://www.phase.eu/⟩ (2007).
Power One. (2007). “Cooling DC-DC converters power-one application note.” ⟨http://www.power-one.com⟩ (2007).
Romeo, G., Borello, F., Cestino, E., Moraglio, I., and Novarese, C. (2007a). “ENFICA-FC environmental friendly inter-city aircraft and 2-seat aircraft powered by fuel cells electric propulsion (DEU).” AIRTEC 2nd Int. Conf.
Romeo, G., Cestino, E., Frulla, G., and Correa, G. (2008). “Summary of support effort activity to new engine cowl design and intakes definition.” ENFICA FC EU-Project Contract No. 30779 Internal Rep. No. D7/6, ENFICA.
Romeo, G., Correa, G., Borello, F., and Pacino, M. (2009). “Integration on board of aircraft and functional ground testing of propulsion system and subsystems. Taxi test.” ENFICA-FC Internal Rep. No. 9/2-3.
Romeo, G., Frulla, G., Cestino, E., and Corsino, G. (2004). “HELIPLAT: Design, aerodynamic, structural analysis of long-endurance solar-powered stratospheric platform.” J. Aircr., 41(6), 1505–1520.
Romeo, G., Novarese, C., and Cestino, E. (2007b). “Design of optimal propeller for the RAPID 200-FC.” ENFICA FC Internal Rep. No. D8/2, ENFICA.
Schouten, G. (1999). “Theodorsen’s propeller performance with rollup and swirl in the slipstream.” J. Aircr., 36(5), 892–895.
Summa, J. M. A. (1987). “Method for computing ducted heat-exchanger flows and its validation for a “front breather” model.” Analytical Methods Rep. No. 8709, Analytical Methods, Washington.
Volker, H. (2006). “Airbus fuel cell systems for aeronautic applications. A clean way from kerosene to energy.” Proc., 25th ICAS Congress.
Information & Authors
Information
Published In
Journal of Aerospace Engineering
Volume 24 • Issue 1 • January 2011
Pages: 79 - 88
Copyright
© 2011 ASCE.
History
Received: Oct 13, 2009
Accepted: Mar 10, 2010
Published online: Mar 24, 2010
Published in print: Jan 2011
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
