Technical Papers
Sep 4, 2018

Fatigue Assessment of Shear-Strengthened RC T-Beams with Externally Bonded CFRP Closed Stirrups

Publication: Journal of Composites for Construction
Volume 22, Issue 6

Abstract

Research studies on reinforced concrete T-beams shear strengthened with externally bonded carbon fiber reinforced polymer (EB-CFRP) have shown that debonding at the CFRP–concrete interface is still a major concern. It is well established that shear strengthening using a full-wrap configuration offers a better solution than side bonding and U-wrap configurations without anchorage systems in preventing premature FRP debonding. However, such a strengthening technique can only be used for rectangular beams for which the four faces are accessible. This is clearly not practical, since most RC beams are cast monolithically with slabs and therefore have a T-section. The objective of the present research was to experimentally assess the effectiveness of a new and innovative EB-CFRP closed-stirrup technology for fatigue upgrade by reproducing the advantages of a full-wrap configuration. The CFRP shear-strengthening system consisted of L-shaped laminates and anchoring ropes to form EB-CFRP closed stirrups. Laboratory tests were performed on full-size RC T-beams with different ratios of internal shear reinforcement under fatigue cyclic loading. The specifications of North American design codes and standards for fatigue limit state design of RC structures were also assessed in this investigation. The EB-CFRP closed stirrups resulted in a decrease in the levels of transverse steel strains and thereby enhanced the fatigue performance of shear-strengthened specimens. The results also demonstrated the existence of an interaction between internal transverse steel and EB-CFRP under fatigue loading. Finally, strengthening with CFRP L-shaped laminates led to a significant increase in the shear resistance of RC T-beams.

Get full access to this article

View all available purchase options and get full access to this article.

Acknowledgments

The financial support of the Natural Sciences and Engineering Research Council of Canada (NSERC) and the Fonds de recherche du Québec—Nature et technologie (FRQNT) through operating grants is gratefully acknowledged. The authors thank Sika Canada Inc. (Pointe Claire, Quebec) for contributing to the cost of the materials. The efficient collaboration of John Lescelleur (senior technician) and Andrés Barco (technician) at École de technologie supérieure (ÉTS) in conducting the tests is acknowledged.

References

AASHTO. 2017. AASHTO LRFD bridge design specifications, 8th edition, with 2015 and 2016 interim revisions. AASHTO LRFD. Washington, DC: AASHTO.
ACI (American Concrete Institute). 1992. Considerations for design of concrete structures subjected to fatigue loading. ACI 215R (R1997). Farmington Hills, MI: ACI.
ACI (American Concrete Institute). 2017. Guide for the design and construction of externally bonded FRP systems for strengthening concrete structures. ACI 440.2R. Farmington Hills, MI: ACI.
ASTM. 2017. Standard test methods and definitions for mechanical testing of steel products. ASTM A370. West Conshohocken, PA: ASTM.
Bae, S. W., and A. Belarbi. 2013. “Behavior of various anchorage systems used for shear strengthening of concrete structures with externally bonded FRP sheets.” J. Bridge Eng. 18 (9): 837–847. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000420.
Bae, S. W., M. Murphy, A. Mirmiran, and A. Belarbi. 2013. “Behavior of RC T-beams strengthened in shear with CFRP under cyclic loading.” J. Bridge Eng. 18 (2): 99–109. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000332.
Baghi, H., and J. A. O. Barros. 2017. “Design approach to determine shear capacity of reinforced concrete beams shear strengthened with NSM systems.” J. Struct. Eng. 143 (8): 04017061. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001793.
Barnes, R. A., and G. C. Mays. 1999. “Fatigue performance of concrete beams strengthened with CFRP plates.” J. Compos. Constr. 3 (2): 63–72. https://doi.org/10.1061/(ASCE)1090-0268(1999)3:2(63).
Bourget, S., G. El-Saikaly, and O. Chaallal. 2017. “Behavior of reinforced concrete T-beams strengthened in shear using closed carbon fiber-reinforced polymer stirrups made of laminates and ropes.” ACI Struct. J. 114 (05): 1087–1098.
Bousselham, A., and O. Chaallal. 2004. “Shear strengthening reinforced concrete beams with fiber-reinforced polymer: Assessment of influencing parameters and required research.” ACI Struct. J. 101 (2): 219–227.
Carolin, A., and B. Täljsten. 2005. “Theoretical study of strengthening for increased shear bearing capacity.” J. Compos. Constr. 9 (6): 497–506. https://doi.org/10.1061/(ASCE)1090-0268(2005)9:6(497).
Chaallal, O., F. Boussaha, and A. Bousselham. 2010. “Fatigue performance of RC beams strengthened in shear with CFRP fabrics.” J. Compos. Constr. 14 (4): 415–423. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000095.
Chaallal, O., M. J. Nollet, and D. Perraton. 1998. “Strengthening of reinforced concrete beams with externally bonded fiber-reinforced-plastic plates: Design guidelines for shear and flexure.” Can. J. Civ. Eng. 25 (4): 692–704. https://doi.org/10.1139/l98-008.
Chaallal, O., M. Shahawy, and M. Hassan. 2002. “Performance of reinforced concrete T-girders strengthened in shear with carbon fiber-reinforced polymer fabric.” ACI Struct. J. 99 (3): 335–343.
Chen, J., and I. N. Robertson. 2004. Test of cracked pre-stressed concrete T-beam retrofitted for shear using CFRP L-shaped plates. Manoa, HI: Univ. of Hawaii Dept. of Civil and Environmental Engineering.
Chen, J. F., and J. G. Teng. 2003. “Shear capacity of fiber-reinforced polymer-strengthened reinforced concrete beams: Fiber reinforced polymer rupture.” J. Struct. Eng. 129 (5): 615–625. https://doi.org/10.1061/(ASCE)0733-9445(2003)129:5(615).
CSA (Canadian Standards Association). 2014. Canadian highway bridge design code. CAN/CSA S6-14. Mississauga, Canada: CSA.
Czaderski, C., and M. Motavalli. 2002. Shear strengthening with prefabricated CFRP L-shaped plates: Test beams S1 to S6. Dübendorf, Switzerland: Eidgenössische Materialprüfungs und Forschungsanstalt.
Czaderski, C., and M. Motavalli. 2004. “Fatigue behaviour of CFRP L-shaped plates for shear strengthening of RC T-beams.” Composites Part B 35 (4): 279–290. https://doi.org/10.1016/j.compositesb.2004.02.001.
D’Antino, T., and C. Pellegrino. 2014. “Bond between FRP composites and concrete: Assessment of design procedures and analytical models.” Composites Part B Eng. 60: 440–456. https://doi.org/10.1016/j.compositesb.2013.12.075.
El-Saikaly, G., and O. Chaallal. 2015a. “Extending the fatigue life of reinforced concrete T-beams strengthened in shear with externally bonded FRP: Upgrading versus repairing.” J. Compos. Constr. 19 (1): 04014027. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000492.
El-Saikaly, G., and O. Chaallal. 2015b. “Fatigue behavior of RC T-beams strengthened in shear with EB CFRP L-shaped laminates.” Composites Part B Eng. 68: 100–112. https://doi.org/10.1016/j.compositesb.2014.08.014.
El-Saikaly, G., A. Godat, and O. Chaallal. 2015. “New anchorage technique for FRP shear-strengthened RC T-beams using CFRP rope.” J. Compos. Constr. 19 (4): 04014064. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000530.
Emberson, N. K., and G. C. Mays. 1996. “Significance of property mismatch in the patch repair of structural concrete. Part 3: Reinforced concrete members in flexure.” Mag. Concr. Res. 48 (174): 45–57. https://doi.org/10.1680/macr.1996.48.174.45.
Eshwar, N., A. Nanni, and T. J. Ibell. 2008. “Performance of two anchor systems of externally bonded fiber-reinforced polymer laminates.” ACI Mater. J. 105 (1): 72–80.
Kalfat, R., R. Al-Mahaidi, and S. T. Smith. 2013. “Anchorage devices used to improve the performance of reinforced concrete beams retrofitted with FRP composites: State-of-the-art review.” J. Compos. Constr. 17 (1): 14–33. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000276.
Khalifa, A., W. J. Gold, A. Nanni, and A. A. Mi. 1998. “Contribution of externally bonded FRP to shear capacity of RC flexural members.” J. Compos. Constr. 2 (4): 195–202. https://doi.org/10.1061/(ASCE)1090-0268(1998)2:4(195).
Khalifa, A., and A. Nanni. 2000. “Improving shear capacity of existing RC T-section beams using CFRP composites.” Cem. Concr. Compos. 22 (3): 165–174. https://doi.org/10.1016/S0958-9465(99)00051-7.
Meier, H. 1998. “CFK-Schubverstärkungselemente.” [In German.] Schweizer Ingenieur und Architekt (SI + A) 43 (22): 819–821.
Mofidi, A., and O. Chaallal. 2011. “Shear strengthening of RC beams with EB FRP: Influencing factors and conceptual debonding model.” J. Compos. Constr. 15 (1): 62–74. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000153.
Mofidi, A., O. Chaallal, B. Benmokrane, and K. Neale. 2012. “Performance of end-anchorage systems for RC beams strengthened in shear with epoxy-bonded FRP.” J. Compos. Constr. 16 (3): 322–331. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000263.
Mofidi, A., S. Thivierge, O. Chaallal, and Y. Shao. 2014. “Behavior of reinforced concrete beams strengthened in shear using L-shaped CFRP plates: Experimental investigation.” J. Compos. Constr. 18 (2): 04013033. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000398.
Pellegrino, C., and C. Modena. 2002. “Fiber reinforced polymer shear strengthening of reinforced concrete beams with transverse steel reinforcement.” J. Compos. Constr. 6 (2): 104–111. https://doi.org/10.1061/(ASCE)1090-0268(2002)6:2(104).
Pellegrino, C., and M. Vasic. 2013. “Assessment of design procedures for the use of externally bonded FRP composites in shear strengthening of reinforced concrete beams.” Composites Part B 45 (1): 727–741. https://doi.org/10.1016/j.compositesb.2012.07.039.
Triantafillou, T. C., and C. P. Antonopoulos. 2000. “Design of concrete flexural members strengthened in shear with FRP.” J. Compos. Constr. 4 (4): 198–205. https://doi.org/10.1061/(ASCE)1090-0268(2000)4:4(198).
Williams, G., and C. Higgins. 2008. “Fatigue of diagonally cracked RC girders repaired with CFRP.” J. Bridge Eng. 13 (1): 24–33. https://doi.org/10.1061/(ASCE)1084-0702(2008)13:1(24).

Information & Authors

Information

Published In

Go to Journal of Composites for Construction
Journal of Composites for Construction
Volume 22Issue 6December 2018

History

Received: Oct 16, 2017
Accepted: May 23, 2018
Published online: Sep 4, 2018
Published in print: Dec 1, 2018
Discussion open until: Feb 4, 2019

Permissions

Request permissions for this article.

Authors

Affiliations

Georges El-Saikaly, Ph.D., M.ASCE [email protected]
P.Eng.
Associate Professor, Dept. of Construction Engineering, École de Technologie Supérieure, Univ. of Quebec, Montreal, QC, Canada H3C 1K3 (corresponding author). Email: [email protected]
Omar Chaallal, Ph.D., F.ASCE [email protected]
P.Eng.
Professor, Dept. of Construction Engineering, École de Technologie Supérieure, Univ. of Quebec, Montreal, QC, Canada H3C 1K3. Email: [email protected]
Brahim Benmokrane, Ph.D. [email protected]
P.Eng.
Professor, Dept. of Civil Engineering, Faculty of Engineering, Univ. of Sherbrooke, Sherbrooke, QC, Canada J1K 2R1. Email: [email protected]

Metrics & Citations

Metrics

Citations

Download citation

If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.

Cited by

View Options

Access content

Please select your options to get access

Log in/Register Log in via your institution (Shibboleth)
ASCE Members: Please log in to see member pricing

Purchase

Save for later Information on ASCE Library Cards
ASCE Library Cards let you download journal articles, proceedings papers, and available book chapters across the entire ASCE Library platform. ASCE Library Cards remain active for 24 months or until all downloads are used. Note: This content will be debited as one download at time of checkout.

Terms of Use: ASCE Library Cards are for individual, personal use only. Reselling, republishing, or forwarding the materials to libraries or reading rooms is prohibited.
ASCE Library Card (5 downloads)
$105.00
Add to cart
ASCE Library Card (20 downloads)
$280.00
Add to cart
Buy Single Article
$35.00
Add to cart

Access content

Please select your options to get access

Log in/Register Log in via your institution (Shibboleth)
ASCE Members: Please log in to see member pricing

Purchase

Save for later Information on ASCE Library Cards
ASCE Library Cards let you download journal articles, proceedings papers, and available book chapters across the entire ASCE Library platform. ASCE Library Cards remain active for 24 months or until all downloads are used. Note: This content will be debited as one download at time of checkout.

Terms of Use: ASCE Library Cards are for individual, personal use only. Reselling, republishing, or forwarding the materials to libraries or reading rooms is prohibited.
ASCE Library Card (5 downloads)
$105.00
Add to cart
ASCE Library Card (20 downloads)
$280.00
Add to cart
Buy Single Article
$35.00
Add to cart

Media

Figures

Other

Tables

Share

Share

Copy the content Link

Share with email

Email a colleague

Share