Technical Papers
Aug 14, 2020

Strain History and Short-Period Aging Effects on the Strength and Cyclic Response of Fine-Grained Coal Refuse

Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 146, Issue 10

Abstract

This paper presents an experimental investigation on the effects of strain history and aging on cyclic response and resistance of fine-grained coal refuse (FCR) using large-scale shaking table tests. The FCR specimen was slurry-deposited in a membrane-lined laminar shear box and subjected to three shaking events on a 1-g shaking table. Sensors were used to measure the FCR’s dynamic response during shaking, and a piezocone penetrometer (CPTu) was used to measure soil resistance and estimate the cyclic behavior of the FCR specimen before and after each shaking test for time intervals up to 97 days. Based on the CPTu tests, the freshly deposited FCR specimen was classified as sensitive fine-grained soil after deposition and self-consolidation. An irregular pore pressure pattern was measured during and after the shakes due to heterogeneity of the FCR specimen. The FCR specimen experienced cyclic mobility and pore pressure redistribution, indicating that the material may be vulnerable to large deformations after cyclic loading. Cone tip resistance immediately after the first shaking event showed limited strength loss due to the original loose structure of the FCR. Each shaking event progressively densified the FCR specimen and increased the cyclic resistance. However, the FCR specimen remained susceptible to cyclic softening and flow liquefaction. The FCR specimen was classified using the CPTu data as clayey silt to silty clay after two shakes and 97 days of aging. Cone tip resistance increased over 100% by 97 days after the second shaking event with a rate of strength increase slower than the rate observed for clean sand in an earlier study. The increase in CPT tip resistance over time was quantified, and an equation to estimate the undrained shear strength of FCR as a function of normalized tip resistance and time after a shaking event was developed and calibrated.

Get full access to this article

View all available purchase options and get full access to this article.

Data Availability Statement

Some or all data, models, or code generated or used during the study are available from the corresponding author by request.

Acknowledgments

Help from graduate students Yen-Chieh Wang, Rong Zhao, and Jintai Wang during the test preparation is greatly acknowledged. The authors appreciate the assistance provided by laboratory specialist Dan Fura to set up the deposition system. The authors also acknowledge the constructive comments and discussions from Patrick Fox during the results analysis and manuscript preparation.

References

Abdoun, T., M. A. Gonzalez, S. Thevanayagam, R. Dobry, A. Elgamal, M. Zeghal, V. M. Mercado, and U. El Shamy. 2013. “Centrifuge and large-scale modeling of seismic pore pressures in sands: Cyclic strain interpretation.” J. Geotech. Geoenviron. Eng. 139 (8): 1215–1234. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000821.
Anderson, D. G., and K. H. Stokoe. 1978. “Shear modulus, a time-dependent soil property.” In Dynamic geotechnical testing, 66–90. West Conshohocken, PA: ASTM. https://doi.org/10.1520/STP35672S.
ASTM. 2012. Standard test method for electronic friction cone and piezocone penetration testing of soils. West Conshohocken, PA: ASTM.
Azam, S., and Q. Li. 2010. “Tailings dam failures: A review of the last one hundred years.” Geotech. News 28 (4): 50–54.
Boggs, S. 2014. Principles of sedimentology and stratigraphy. London: Pearson.
Boulanger, R. W., and I. M. Idriss. 2006. “Liquefaction susceptibility criteria for silts and clays.” J. Geotech. Geoenviron. Eng. 132 (11): 1413–1426. https://doi.org/10.1061/(ASCE)1090-0241(2006)132:11(1413).
Boulanger, R. W., and I. M. Idriss. 2007. “Evaluation of cyclic softening in silts and clays.” J. Geotech. Geoenviron. Eng. 133 (6): 641–652. https://doi.org/10.1061/(ASCE)1090-0241(2007)133:6(641).
Burns, S. E., and P. W. Mayne. 1998. “Monotonic and dilatory pore-pressure decay during piezocone tests in clay.” Can. Geotech. J. 35 (6): 1063–1073. https://doi.org/10.1139/t98-062.
Castro, G. 1987. “On the behavior of soils during earthquakes—Liquefaction.” In Developments in geotechnical engineering, 169–204. Amsterdam, Netherlands: Elsevier.
Castro, G. 2003. “Evaluation of seismic stability of tailings dams.” In Proc., 12th Pan-American Conf. on Soil Mechanics and Geotechnical Engineering, 16–23. London: International Society for Soil Mechanics and Geotechnical Engineering.
Charlie, W. A., M. F. Rwebyogo, and D. O. Doehring. 1992. “Time-dependent cone penetration resistance due to blasting.” J. Geotech. Eng. 118 (8): 1200–1215.
Dowding, C. H., and R. D. Hryciw. 1986. “A laboratory study of blast densification of saturated sand.” J. Geotech. Eng. 112 (2): 187–199. https://doi.org/10.1061/(ASCE)0733-9410(1986)112:2(187).
El-Sekelly, W., T. Abdoun, and R. Dobry. 2016a. “Liquefaction resistance of a silty sand deposit subjected to preshaking followed by extensive liquefaction.” J. Geotech. Geoenviron. Eng. 142 (4): 04015101. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001444.
El-Sekelly, W., R. Dobry, T. Abdoun, and J. H. Steidl. 2016b. “Centrifuge modeling of the effect of pre-shaking on the liquefaction resistance of silty sand deposits.” J. Geotech. Geoenviron. Eng. 142 (6): 04016012. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001430.
Finn, W. D. L., P. L. Bransby, and D. J. Pickering. 1970. “Effect of strain history on liquefaction of sand.” J. Soil Mech. Found. Div. 96 (6): 1917–1934.
Geremew, A. M., and E. K. Yanful. 2012. “Dynamic properties and influence of clay mineralogy types on the cyclic strength of mine tailings.” Int. J. Geomech. 13 (4): 441–453. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000227.
Heidari, T., and R. D. Andrus. 2012. “Liquefaction potential assessment of Pleistocene beach sands near Charleston, South Carolina.” J. Geotech. Geoenviron. Eng. 138 (10): 1196–1208. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000686.
Idriss, I. M., and R. W. Boulanger. 2008. Soil liquefaction during earthquakes. Oakland, CA: Earthquake Engineering Research Institute.
Ishihara, K., S. Yasuda, and K. Yokota. 1981. Cyclic strength of undisturbed mine tailings. Columbia, MO: Univ. of Missouri.
James, M., M. Aubertin, D. Wijewickreme, and G. W. Wilson. 2011. “A laboratory investigation of the dynamic properties of tailings.” Can. Geotech. J. 48 (11): 1587–1600. https://doi.org/10.1139/t11-060.
Jefferies, M. G., and M. P. Davies. 1991. “Soil classification by the cone penetration test: Discussion.” Can. Geotech. J. 28 (1): 173–176. https://doi.org/10.1139/t91-023.
Joshi, R. C., G. Achari, S. R. Kaniraj, and H. Wijeweera. 1995. “Effect of aging on the penetration resistance of sands.” Can. Geotech. J. 32 (5): 767–782.
Kalinski, M. E., and A. Salehian. 2016. “Estimating the cyclic and post-earthquake behavior of coal mine tailings at a site in eastern Kentucky.” In Proc., Geo-Chicago 2016, 279–288. Reston, VA: ASCE.
Kim, T. C., and M. Novak. 1981. “Dynamic properties of some cohesive soils of Ontario.” Can. Geotech. J. 18 (3): 371–389.
Martin, T. E., and M. P. Davies. 2000. “Development and review of surveillance programs for tailings dams.” In Proc., Tailings Dams 2000. Lexington, KY: Association of State Dam Safety Officials.
Mesri, G., T. W. Feng, and J. M. Benak. 1990. “Postdensification penetration resistance of clean sands.” J. Geotech. Eng. 116 (7): 1095–1115. https://doi.org/10.1061/(ASCE)0733-9410(1990)116:7(1095).
Mitchell, J. K., and Z. V. Solymar. 1984. “Time-dependent strength gain in freshly deposited or densified sand.” J. Geotech. Eng. 110 (11): 1559–1576. https://doi.org/10.1061/(ASCE)0733-9410(1984)110:11(1559).
Moss, R. E., R. B. Seed, R. E. Kayen, J. P. Stewart, A. Der Kiureghian, and K. O. Cetin. 2006. “CPT-based probabilistic and deterministic assessment of in situ seismic soil liquefaction potential.” J. Geotech. Geoenviron. Eng. 132 (8): 1032–1051. https://doi.org/10.1061/(ASCE)1090-0241(2006)132:8(1032).
Price, A. B., J. T. DeJong, and R. W. Boulanger. 2017. “Cyclic loading response of silt with multiple loading events.” J. Geotech. Geoenviron. Eng. 143 (10): 04017080. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001759.
Rico, M., G. Benito, A. R. Salgueiro, A. Díez-Herrero, and H. G. Pereira. 2008. “Reported tailings dam failures: A review of the European incidents in the worldwide context.” J. Hazard. Mater. 152 (2): 846–852. https://doi.org/10.1016/j.jhazmat.2007.07.050.
Robertson, P. K. 2009. “Evaluation of flow liquefaction and liquefied strength using the cone penetration test.” J. Geotech. Geoenviron. Eng. 136 (6): 842–853. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000286.
Robertson, P. K. 2016. “Cone penetration test (CPT)-based soil behavior type (SBT) classification system—An update.” Can. Geotech. J. 53 (12): 1910–1927. https://doi.org/10.1139/cgj-2016-0044.
Robertson, P. K., A. V. da Fonseca, B. Ulrich, and J. Coffin. 2017. “Characterization of unsaturated mine waste: A case history.” Can. Geotech. J. 54 (12): 1752–1761. https://doi.org/10.1139/cgj-2017-0129.
Robertson, P. K., and C. E. Wride. 1998. “Evaluating cyclic liquefaction potential using the cone penetration test.” Can. Geotech. J. 35 (3): 442–459. https://doi.org/10.1139/t98-017.
Salam, S., M. Xiao, A. Khosravifar, M. Liew, S. Liu, and J. Rostami. 2019. “Characterizations of static and dynamic geotechnical properties and behaviors of fine coal refuse.” Can. Geotech. J. 56 (12): 1901–1916. https://doi.org/10.1139/cgj-2018-0630.
Salam, S., M. Xiao, and J. Wang. 2020. “Physical modeling of fine coal refuse using shake table testing.” In Proc., GeoCongress 2020: Earthquake Engineering and Soil Dynamics. Reston, VA: ASCE.
Salehian, A. 2013. “Predicting the dynamic behavior of coal mine tailings using state-of-practice geotechnical field methods.” Ph.D. dissertation, Dept. of Civil Engineering, Univ. of Kentucky.
Schmertmann, J., W. Baker, R. Gupta, and K. Kessler. 1986. “CPT/DMT QC of ground modification at a power plant.” In Use of in situ tests in geotechnical engineering, 985–1001. Reston, VA: ASCE.
Seed, H. B., and I. M. Idriss. 1971. “Simplified procedure for evaluating soil liquefaction potential.” J. Soil Mech. Found. Div. 97 (SM9): 1249–1273.
Seed, H. B., P. P. Martin, and J. Lysmer. 1975. The generation and dissipation of pore water pressures during soil liquefaction. Oakland, CA: Univ. of California.
Seed, R. B. et al. 2003. “Recent advances in soil liquefaction engineering: A unified and consistent framework.” In Proc., 26th Annual ASCE Los Angeles Geotechnical Spring Seminar. Reston, VA: ASCE.
Shuttle, D. A., and J. Cunning. 2007. “Liquefaction potential of silts from CPTu.” Can. Geotech. J. 44 (1): 1–19. https://doi.org/10.1139/t06-086.
Solymar, Z. V. 1984. “Compaction of alluvial sands by deep blasting.” Can. Geotech. J. 21 (2): 305–321.
Teparaksa, J., and J. Koseki. 2018. “Effect of past history on liquefaction resistance of level ground in shaking table test.” Géotechnique Lett. 8 (4): 256–261. https://doi.org/10.1680/jgele.18.00085.
Terzaghi, K., R. B. Peck, and G. Mesri. 1996. Soil mechanics in engineering practice. Hoboken, NJ: Wiley.
Wang, J., M. Xiao, J. C. Evans, T. Qiu, and S. Salam. 2019. “Time-dependent cone penetration resistance of a postliquefaction sand deposit at shallow depth.” J. Geotech. Geoenviron. Eng. 145 (6): 04019021. https://doi.org/10.1061/(ASCE)GT.1943-5606.0002049.
Whitman, R. V. 1970. “Hydraulic fills to support structural loads.” J. Soil Mech. Found. Div. 96 (1): 23–47.
Xiao, M., M. Liew, S. Salam, S. Liu, and J. Rostami. 2019. Field investigation and stability analysis of coal slurry impoundments. Washington, DC: US Office of Surface Mining Reclamation and Enforcement.
Yang, J. 2006. “Influence zone for end bearing of piles in sand.” J. Geotech. Geoenviron. Eng. 132 (9): 1229–1237. https://doi.org/10.1061/(ASCE)1090-0241(2006)132:9(1229).
Youd, T. L., and I. M. Idriss. 1998. “Workshop on evaluation of liquefaction resistance of soils.” In Proc., National Center for Earthquake Engineering Research (NCEER). Taipei, Taiwan: National Center for Earthquake Engineering Research.
Zeng, X., J. A. Goble, and L. Fu. 2008. “Dynamic properties of coal waste refuse in a tailings dam.” In Geotechnical earthquake engineering and soil dynamics IV, 1–14. Reston, VA: ASCE.

Information & Authors

Information

Published In

Go to Journal of Geotechnical and Geoenvironmental Engineering
Journal of Geotechnical and Geoenvironmental Engineering
Volume 146Issue 10October 2020

History

Received: Oct 21, 2019
Accepted: May 29, 2020
Published online: Aug 14, 2020
Published in print: Oct 1, 2020
Discussion open until: Jan 14, 2021

Permissions

Request permissions for this article.

Authors

Affiliations

Sajjad Salam, Ph.D., S.M.ASCE [email protected]
Dept. of Civil and Environmental Engineering, Pennsylvania State Univ., University Park, PA 16801 (corresponding author). Email: [email protected]
Ming Xiao, Ph.D., F.ASCE [email protected]
Associate Professor, Dept. of Civil and Environmental Engineering, Pennsylvania State Univ., University Park, PA 16802. Email: [email protected]
Jeffrey C. Evans, Ph.D., F.ASCE [email protected]
Professor, Dept. of Civil and Environmental Engineering, Bucknell Univ., Lewisburg, PA 17837. Email: [email protected]

Metrics & Citations

Metrics

Citations

Download citation

If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.

Cited by

View Options

Access content

Please select your options to get access

Log in/Register Log in via your institution (Shibboleth)
ASCE Members: Please log in to see member pricing

Purchase

Save for later Information on ASCE Library Cards
ASCE Library Cards let you download journal articles, proceedings papers, and available book chapters across the entire ASCE Library platform. ASCE Library Cards remain active for 24 months or until all downloads are used. Note: This content will be debited as one download at time of checkout.

Terms of Use: ASCE Library Cards are for individual, personal use only. Reselling, republishing, or forwarding the materials to libraries or reading rooms is prohibited.
ASCE Library Card (5 downloads)
$105.00
Add to cart
ASCE Library Card (20 downloads)
$280.00
Add to cart
Buy Single Article
$35.00
Add to cart

Access content

Please select your options to get access

Log in/Register Log in via your institution (Shibboleth)
ASCE Members: Please log in to see member pricing

Purchase

Save for later Information on ASCE Library Cards
ASCE Library Cards let you download journal articles, proceedings papers, and available book chapters across the entire ASCE Library platform. ASCE Library Cards remain active for 24 months or until all downloads are used. Note: This content will be debited as one download at time of checkout.

Terms of Use: ASCE Library Cards are for individual, personal use only. Reselling, republishing, or forwarding the materials to libraries or reading rooms is prohibited.
ASCE Library Card (5 downloads)
$105.00
Add to cart
ASCE Library Card (20 downloads)
$280.00
Add to cart
Buy Single Article
$35.00
Add to cart

Media

Figures

Other

Tables

Share

Share

Copy the content Link

Share with email

Email a colleague

Share