Effect of Warm Temperatures on Externally Bonded FRP Strengthening
Publication: Journal of Composites for Construction
Volume 16, Issue 3
Abstract
Fiber-reinforced polymer (FRP) plate strengthening relies critically upon the adhesive that is used to bond it to the existing structure. A typical two-part ambient-cure epoxy adhesive for structural strengthening has a glass transition temperature of approximately 40°C–70°C, but the stiffness and strength of the adhesive typically decrease at temperatures somewhat below this characteristic temperature. This paper investigates the implications of the changes in adhesive properties at warm temperatures () for FRP-strengthened beams, through short-term experimental and analytical work. Tests were conducted on FRP-strengthened steel beams subjected to sustained load and increasing temperature; the results, however, are also relevant to strengthened concrete beams. Digital image correlation was used to measure the slip between the strengthening plate and beam, and hence to observe the behavior of the adhesive joint. A bond analysis was also developed to predict the slip across the adhesive joint at an elevated temperature, based upon the glass transition characteristics of the adhesive measured using dynamic mechanical analysis. The analysis allows the response of the strengthened beams to warm temperatures to be examined in further detail. Both the experimental and analytical results show that substantial slip can occur between the plate and beam at temperatures over 40°C. As the temperature increases and the adhesive softens, a greater length of adhesive joint is required to transfer load from the plate to the beam, resulting in an increase in slip that eventually causes debonding of the plate from the beam.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The experiments were undertaken by Cameron Gillespie and Martin Moran during their undergraduate theses, and the School of Engineering at the University of Edinburgh is thanked for its support of these projects. Dr. Andy Take of Queen’s University, Canada, is thanked for allowing access to the GeoPIV digital image correlation software. The Scottish Funding Council is thanked for its support of the Joint Research Institute for Civil and Environmental Engineering, part of the Edinburgh Research Partnership in Engineering and Mathematics (ERPem). Dr. Bisby gratefully acknowledges the support of the Ove Arup Foundation and the Royal Academy of Engineering.
References
American Concrete Institute (ACI). (2008). “Guide for the design and construction of externally bonded FRP systems for strengthening concrete structures.” American Concrete Institute Rep. ACI 440.2R-08, Farmington Hills, MI.
Ashby, M. F., and Jones, D. R. H. (1986). Engineering materials 2, Pergamon Press, Oxford, U.K.
Blondtrock, H., Taerwe, L., and Vandevelde, P. (2001). “Fire testing of concrete slabs strengthened with fibre composite laminates.” Proc. FRPRCS-5, Thomas Telford, London.
Concrete Society. (2004). “Design guidance for strengthening concrete structures using fibre composite materials.” Technical Rep. 55, 2nd Ed., Camberley, U.K.
Consiglio Nazionale delle Richerche (CNR). (2007). “Guidelines for the design and construction of externally bonded FRP systems for strengthening existing structures. Metallic sructures.” Italian National Research Council Rep. CNR-DT 202/2005, Rome.
Construction Industry Research and Information Association (CIRIA). (2004). “Strengthening metallic structures using externally bonded fibre-reinforced polymers.” Report C595, London.
Deng, J., Lee, M. M. K., and Moy, S. S. J. (2004). “Stress analysis of steel beams reinforced with a bonded CFRP plate.” Compos. Struct.COMSE2, 65(2), 205–215.
Denton, S. R. (2001). “Analysis of stresses developed in FRP plated beams due to thermal effects.” 1st Int. Conf. on FRP Composite in Civil Engineering, Elsevier Science, Oxford, 527–536.
Gullapalli, A., Lee, J. H., Lopez, M. M., and Bakis, C. E. (2009). “Sustained loading and temperature response of fiber-reinforced polymer-concrete bond.” Transportation Research Record 2131, Transportation Research Board, Washington, DC, 155–162.
Highways Agency. (2001). “Loads for highways bridges.” Design manual for roads and bridges, BD37/01, The Stationary Office Ltd., London.
ISO. (2002). “Plastics. Determination of dynamic mechanical properties. General principles.” ISO 6721-1, British Standards Institution, London, UK.
Jaipuriar, A., Flood, J. P., Bakis, C. E., Lopez, M. M., and He, X. (2010). “Glassy-rubbery transition behavior of epoxy resins used in FRP structural strengthening systems.” 5th Int. Conf. on FRP Composites in Civil Engineering, Springer, Heidelberg, Germany.
Klamer, E. L., Hordijk, D. A., and Hermes, M. C. J. (2008). “The influence of temperature on RC beams strengthened with externally bonded CFRP reinforcement.” HeronHERNDU, 53(3), 157–186.
Kodur, V. K. R., Bisby, L. A., and Green, M. F. (2007). “Preliminary guidance for the design of FRP-strengthened concrete members exposed to fire.” J. Fire Prot. Eng.JFPEEN, 17(1), 5–26.
Ludwig, C., Knippers, J., Hugi, E., and Ghazi, W. K. (2008). “Damage of flexural loaded composite beams subjected to fire.” 4th Int. Conf. on FRP Composites in Civil Engineering, EMPAAkademie, Zurich, 527–536.
Mazzotti, C., and Savoia, M. (2009). “Stress redistribution along the interface between concrete and FRP subject to long-term loading.” Adv. Struct. Eng., 12(5), 651–661.
Porter, M. L., and Harries, K. (2007). “Future directions for research in FRP composites in concrete construction.” J. Compos. Constr.JCCOF2, 11(3), 252–257.
Schnerch, D., Dawood, M., and Rizkalla, S. (2007). “Design guidelines for the use of HM strips: Strengthening of steel concrete composite bridges with high modulus carbon fibre reinforced polymer (CFRP) strips.” Technical Rep. No. IS-06-02, Constructed Facilities Laboratory, NC State Univ., Raleigh, NC.
Smith, S. T., and Teng, J. G. (2001). “Interfacial stresses in plated beams.” Eng. Struct.ENSTDF, 23(7), 857–871.
Stratford, T., and Cadei, J. (2006). “Elastic analysis of adhesion stresses for the design of a strengthening plate bonded to a beam.” Constr. Build. Mater.CBUMEZ, 20(1–2), 34–45.
Stratford, T. J., Gillie, M., Chen, J. F., and Usmani, A. S. (2009). “Bonded fibre reinforced polymer strengthening in a real fire.” Adv. Struct. Eng., 12(6), 867–878.
White, D. J., Take, W. A., and Bolton, M. D. (2003). “Soil deformation measurement using particle image velocimetry (PIV) and photogrammetry.” GeotechniqueGTNQA8, 53(7), 619–631.
Information & Authors
Information
Published In
Copyright
© 2012. American Society of Civil Engineers.
History
Received: Oct 11, 2010
Accepted: Oct 14, 2011
Published online: Oct 18, 2011
Published in print: Jun 1, 2012
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.